Manual DeWalt DWE4203 Angle Grinder

Manual

7

ENGLISH

n) Regularly clean the power tool’s air vents.

The motor’s fan will draw the dust inside

the housing and excessive accumulation of

powdered metal may cause electricalhazards.

o) Do not operate the power tool near

flammable materials. Sparks could ignite

thesematerials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution orshock.

q) Do not use Type 11 (flaring cup) wheels on

this tool. Using inappropriate accessories can

result ininjury.

r) Always use side handle. Tighten the handle

securely. The side handle should always be

used to maintain control of the tool at alltimes.

FURTHER SAFETY INSTRUCTIONS

FOR ALL OPERATIONS

Causes and Operator Prevention

of Kickback

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in turn

causes the uncontrolled power tool to be forced in

the direction opposite of the accessory’s rotation at

the point of thebinding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into

the surface of the material causing the wheel to

climb out or kick out. The wheel may either jump

toward or away from the operator, depending on

direction of the wheel’s movement at the point of

pinching. Abrasive wheels may also break under

theseconditions.

Kickback is the result of tool misuse and/or incorrect

operating procedures or conditions and can be

avoided by taking proper precautions as given

below:

a) Maintain a firm grip on the power tool and

position your body and arm to allow you to

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control

over kickback or torque reaction during start

up. The operator can control torque reaction or

kickback forces, if proper precautions aretaken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over

yourhand.

diameter of the flange. Accessories that do

not match the mounting hardware of the power

tool will run out of balance, vibrate excessively

and may cause loss ofcontrol.

g) Do not use a damaged accessory. Before

each use inspect the accessory such as

abrasive wheel for chips and cracks, backing

pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power

tool or accessory is dropped, inspect for

damage or install an undamaged accessory.

After inspecting and installing an accessory,

position yourself and bystanders away from

the plane of the rotating accessory and run

the power tool at maximum no-load speed

for one minute. Damaged accessories will

normally break apart during this testtime.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping flying debris generated

by various operations. The dust mask or

respirator must be capable of filtrating particles

generated by your operation. Prolonged

exposure to high intensity noise may cause

hearingloss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken

accessory may fly away and cause injury

beyond immediate area ofoperation.

j) Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting

accessory contacting a "live" wire may make

exposed metal parts of the power tool "live" and

could give the operator an electricalshock.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord may be

cut or snagged and your hand or arm may be

pulled into the spinningaccessory.

l) Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grab the surface and

pull the power tool out of yourcontrol.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into yourbody.

Rating

More about this manual

We understand that it’s nice to have a paper manual for your DeWalt DWE4203 Angle Grinder. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact DeWalt. They might be able to provide an original manual. Are you looking for the manual of your DeWalt DWE4203 Angle Grinder in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for DeWalt Angle Grinders
More manuals of Angle Grinders

Frequently Asked Questions about DeWalt DWE4203 Angle Grinder

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

DeWalt DWE4012 Angle Grinder

Manual

DeWalt DWE46153 Angle Grinder

Manual

DeWalt DWE4057 Angle Grinder

Manual

DeWalt DWE4227 Angle Grinder

Manual

DeWalt D28115N Angle Grinder

Manual

DeWalt DWE46101 Angle Grinder

Manual

DeWalt DWE46102 Angle Grinder

Manual

DeWalt D28423 Angle Grinder

Related categories