in category III overvoltage conditions, in accordance with
the installation rules. • Warning! The power cable must be
replaced by the authorised technical support service or by a
person with similar qualifications.
● Please note! Before reconnecting the circuit to the
mains power supply, make sure that it is working correctly,
always check that the power cable is correctly installed.
Please note! Do not use with a programmer, timer, sepa-
rate remote control or any other device that activates auto-
matically.
RECOMMENDATIONS FOR USE
Recommendations for correct use in order to reduce the
impact on the environment: When cooking begins, the de-
vice should be turned on at minimum speed, and left on for
a few minutes even after cooking is complete. Increase the
speed only if there is a large quantity of fumes and steam,
using the Booster function only in extreme cases. To keep
the odour reduction system running efficiently, replace the
carbon filter/s when necessary. To ensure the high perfor-
mance of the grease filter, clean it when necessary. To im-
prove efficiency and minimise noise, use the maximum
duct diameter indicated in this manual.
END-OF-LIFE DISPOSAL
This appliance is marked with the separate col-
lection symbol for waste electrical and electronic
equipment (WEEE).
This means that this product must be taken care
of by a separate collection system in accordance
with the European Directive 2012/19/EC in order
to be disassembled or recycled, and thus reduce
the impact on the environment.
For more information, you can contact the local administra-
tion (municipality) or regional.Electronic products that have
not undergone selective sorting are potentially dangerous
for the environment due to the presence of hazardous sub-
stances.
IMPORTANT: Under no circumstances should you dispose
of your device or battery on public roads.
REGULATIONS
Equipment designed, tested and manufactured in compli-
ance with safety regulations: EN/IEC 60335-1; EN/IEC
60335-2- 31, EN/IEC 62233. Performance: EN/IEC 61591;
ISO 5167-1; ISO 5167-3; ISO 5168; EN/IEC 60704-1; EN/
IEC 60704-2-13;EN/IEC 60704-3; ISO 3741; EN 50564;
IEC 62301. EMC: EN 55014-1; CISPR 14-1; EN 55014-2;
CISPR 14-2; EN/IEC 61000-3-2; EN/IEC 61000-3-3.
2. USE
The extraction system can be used in the duct-out version
with external evacuation, or in the recirculating version with
filtering and internal recirculation.
● Duct-Out Version:
Vapours are evacuated outside through an exhaust pipe at-
tached to the connecting flange.
CAUTION! If the product features one or more carbon fil-
ters, they must be removed.
Connect the product to wall-mounted exhaust pipes and
holes with a diameter equivalent to the air outlet (connect-
ing flange).
The use of pipes and outlet holes in the wall with a smaller
diameter will reduce the extraction performance and drasti-
cally increase the noise level.
All responsibility in this regard is therefore denied.
• Use a ducting pipe with the shortest length necessary.
• Use a ducting pipe with the least number of bends possi-
ble (maximum bend angle: 90°).
• Avoid drastic changes in the ducting pipe diameter.
● Recirculating Version:
The suctioned air will be degreased and deodorised before
it is sent back into the room. To use the product in this ver-
sion, it is necessary to install an additional activated carbon
filter system.
ASSEMBLY BEFORE INSTALLATION
• Check that the product is the right size for the installation
area.
• Remove the activated carbon filter(s) if supplied (see also
relevant paragraph).
• It(they) must be reinstalled if the product is used in the fil-
ter version.
• If there are panels and/or walls and/or wall units on the
sides, make sure that there is enough space to install the
product and that it is always possible to access the control
panel easily.
• Do not make any modifications to the device or its mount-
ing bracket on the wall!
• Ask a professional to fix the hood to the wall.
• The wall on which the hood will be fixed must be in good
condition and must not show any damage (cracks, subsid-
ence, humidity, etc.). It must also be strong enough to sup-
port the weight of the hood.
• Do not drill a hole close to old holes, even filled ones.
• It is essential to consult a building professional to use the
anchoring system (screws, dowels, etc.) appropriate to the
material that makes up your wall, as well as to the weight of
the appliance. Respect the diameter of the fixing screws in-
dicated in this manual.
Note: The fixing screws and dowels supplied with the prod-
uct can only be used if they are suitable for your wall type.
If the screws and dowels provided are not suitable for the
type of your wall, it is essential to use an appropriate sys-
tem recommended by the professional installer.
• The holes intended for fixing the appliance or its mounting
bracket to the wall must not be modified.
• The wall must be drilled using a drill of the correct size for
4
Join the conversation about this product
Here you can share what you think about the Continental Edison CEHD6065B Cooker Hood. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.