Manual Casio 5526 (MRG) Movement

Manual

User’s Guide 5526 (MRG)

E-15

Time Zone setting

Important!

x In order to prevent loss of water resistance and damage due to impact, make sure that the crown is

fully pushed in to its normal position after operating it.

x For details about summer time settings and time zone settings, refer to the Operation Guide available

at the CASIO website.

http://world.casio.com/manual/wat/

E-14

Using the Watch in a Medical Facility or Aircraft

x Disable auto time adjustment whenever you are in a medical facility, and aircraft, in any other area

where radio wave reception and connection with a phone are prohibited or restricted.

x Disabling auto time adjustment disables time calibration signal auto receive and auto connection with

a phone.

x Press B once and then pull out the crown to the first click. The second hand will move to Y (YES)

(auto receive enabled) or N (NO) (auto receive disabled). To disable auto time adjustment, rotate the

crown to move the second hand to N (NO). To enable auto time adjustment, rotate the crown to

move the second hand to Y (YES). After the setting is the way you want, push the crown back in to its

normal position.

30

E-13

C

Stopwatch Mode Countdown Timer Mode

30

x Start

x Stop

Seconds

x Reset x Enters the

Countdown

Timer Mode

Points to ST

Hours

Minutes

Hours

(0 to 24)

C

30

x Start

x Stop

Seconds

x Reset x Enters the

Alarm Mode

Points to TR

Hours

Minutes

Hours

(0 to 24)

C

Alarm Mode

* The A-side of the dial indicates an a.m. time, while

the P-side indicates a p.m. time.

x Hold down C for about four seconds to establish

a Bluetooth connection with a phone. For details,

refer to the Operation Guide available at the CASIO

website.

http://world.casio.com/manual/wat/

30

x Illumination

Alarm on

x Alarm off x Enters the

Timekeeping

Mode

Points to AL

Hours

Minutes

Hours

(0 to 24)

x Holding down C for two seconds in any mode returns to the Timekeeping Mode.

E-12

Mode Reference Guide

x Use C to navigate between modes.

Timekeeping Mode

30

Minute hand

Day of the week

hand

24-hour hand

Hour hand

Second hand

Day Indicator

Crown

CB

A

Dual time hour hand

Dual time 24-hour hand*

Dual time minute hand

x Pressing A turns on the illumination.

x To swap your Home Time with the Dual Time,

hold down A for threeseconds.

x To view the result of last time calibration by

time signal reception or Mobile Link, press

B once.

x To trigger a time calibration by Mobile Link

manually, hold down B for 0.5seconds.

x To trigger a time calibration signal reception

operation manually, hold down B for

1.5seconds.

x To search for the phone (while the watch

is connected with it), hold down B for

3.5seconds.

x Press C once to enter the Stopwatch Mode.

C

E-11

Time Calibration Signal Manual Receive

1. Hold down B for at least two seconds until the second hand moves

to RC (Receive). If the second hand is a position other than RC, keep

B depressed until it moves to RC.

2. Place the watch near a window.

x The time setting will be adjusted automatically when a signal receive

operation is successful.

x Calibration signal reception normally takes anywhere from about two

to 10 minutes. It can take as long as 20 minutes.

x Best reception is in the middle of the night.

x If you are unable to receive a signal, check the Operation Guide

available at the CASIO website to ensure the watch is in a suitable

location.

http://world.casio.com/manual/wat/

30

Second hand

E-10

Time Calibration Signal Auto Receive

Important!

x To perform time calibration signal auto receive, the watch must be in the Timekeeping Mode. See

“Mode Reference Guide” (page E-12).

●

Leave the watch in a location that is appropriate for time calibration signal reception between

the hours of midnight and 5:00 a.m. See “Appropriate Signal Reception Location (Time

Calibration Signal)” (page E-9).

x The second hand will point to RC while time calibration signal reception is in progress.

x Reception normally takes anywhere from about two to ten minutes, but it can take as long as

20minutes.

x When the receive operation is successful, the time and day settings will be adjusted automatically.

E-9

Timekeeping (Based on a Time Calibration Signal)

Appropriate Signal Reception Location (Time Calibration Signal)

x Keep the watch away from metal and position it so its 6 o’clock side is

facing a window. Avoid moving the watch as much as possible and do

not perform any watch operations while a signal receive operation is in

progress.

●

You may experience time calibration signal reception problems in

the areas described below.

- Among or near buildings

- While riding in a vehicle

- Near household appliances, office machines, mobile phones, etc.

- On a construction site, in an airport, or any other location where radio

wave interference occurs

- Near high-voltage lines

- In mountainous areas or behind a mountain

x Always check the time setting on the day there should be a switch

between standard time and summer time (DST). If the setting is not

correct (due to signal reception failure), turn DST on or off manually as

required.

6 o’clock

E-8

Timekeeping (Current Time and Day Adjustment)

●

Timekeeping is kept accurate using information provided by a time calibration signal and by

communication with a mobile phone.

x Time calibration signals can be received using Auto Receive or Manual Receive (page E-9).

x To set the current time and day, normally use the procedure under “Time Calibration Signal Auto

Receive” (page E-10).

x For information about how to adjust time using a phone, refer to the Operation Guide available at

the website below.

http://world.casio.com/manual/wat/

x If you are in an area where a time calibration signal cannot be received or if you cannot connect

with a phone for some reason, adjust time and date settings manually (page E-18).

Important!

x If you feel that the current time and/or day indicator are not in the correct positions, you can adjust

their alignment. For details, see the Operation Guide available at the CASIO website.

x Time calibration signal reception is normally possible in the areas below.

Japan, China, North America, Europe

For details, see the Operation Guide available at the CASIO website.

x For details about the following operations, refer to the Operation Guide available at the CASIO website:

Configuring Home City time differential (time zone), summer time, current time, and current date

settings manually.

http://world.casio.com/manual/wat/

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Casio 5526 (MRG) Movement. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Casio. They might be able to provide an original manual. Are you looking for the manual of your Casio 5526 (MRG) Movement in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Casio Movements
More manuals of Movements

Frequently Asked Questions about Casio 5526 (MRG) Movement

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Casio 5531 (MRG) Movement

Manual

Casio 5560 Movement

Manual

Casio 5513 Movement

Manual

Casio 5460 Movement

Manual

Casio 5536 Movement

Manual

Casio 5419 Movement

Manual

Casio 5537 Movement

Manual

Casio 3468 Movement

Related categories