Home > Garden & Terrace > Grass Trimmers > Black and Decker Grass Trimmers > Black and Decker GLC3630L20 Grass Trimmer

Manual Black and Decker GLC3630L20 Grass Trimmer

Name: Black and Decker GLC3630L20 Grass Trimmer
Brand: Black and Decker
SKU: GLC3630L20
Rating: 77 (13 reviews)

Need a manual for your Black and Decker GLC3630L20 Grass Trimmer? Below you can view and download the PDF manual for free in English. This product currently has 0 frequently asked questions, 4 comments and has 13 votes with an average product rating of 77/100. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

ENGLISH

(Original instructions)

Chargers

u Use your BLACK+DECKER charger only to charge the

battery in the tool with which it was supplied. Other

batteries could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

Electrical safety

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This appliance includes some or all of the following features.

1. On/off switch

2. Handle

3. Lock off button

4. Battery

5. Second handle

6. Guard

7. Spool housing

8. Head

9. Edge guide

Assembly

Warning! Before assembly, make sure that the tool is

switched off and the battery has been removed.

Fitting the guard (g. A & B)

u Remove the screw from the guard.

u Keeping the guard (6) square to the strimmer head (8)

slide it into place until the retaining tab clicks into place

(Ensure that the guide rails (10) on the guard (6) are

correctly aligned with the guide rails (11) on the strimmer

head (8).

u Secure the guard (6) with the screw (12).

Warning! Never use the tool unless the guard is properly

tted.

Attaching the second handle (g. C & D )

u Position the second handle (5) over the the tube (13)

u Slide the bolt (14) through the holes in the second handle.

u Tighten the knob (15) onto the bolt by turning it clockwise.

Adjusting the position of the secondary handle (g.

C & D)

The second handle (5) can be adjusted to provide optimum

balance and comfort.

u Loosen the knob (15) on the bolt by turning it anti-

clockwise.

u Gently slide the second handle (5) up or down the tube

(13) to the desired height.

u Tighten the knob (15) onto the bolt by turning it clockwise.

Adjusting the height of the tool (g. E)

This tool has a telescopic mechanism, allowing you to set it to

a comfortable height. There are multiple height settings.

To adjust the height setting, proceed as follows:

u Release the height adjust locking clamp (16).

u Gently pull the tube (17) up or down to the desired height.

u Close the height adjust locking clamp (16).

Releasing the cutting line

In transit, the cutting line is taped to the spool housing.

Warning! Before assembly, remove the battery from the tool.

u Remove the tape holding the cutting line to the spool

housing (7).

Fitting and removing the battery (g. F)

u To t the battery (4), line it up with the receptacle on the

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (18) while

at the same time pulling the battery out of the receptacle.

Use

Warning! Let the tool work at its own pace. Do not overload.

Download manual in English (PDF, 5.64 MB)

(Consider the environment and only print this manual if it is really necessary)

Rating

Let us know what you think about the Black and Decker GLC3630L20 Grass Trimmer by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the Black and Decker GLC3630L20 Grass Trimmer?
Yes No

77%

23%

13 votes

Join the conversation about this product

Here you can share what you think about the Black and Decker GLC3630L20 Grass Trimmer. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

mervyn richard greenwood 22-08-2021
shaft not inguaging how do i remove head to investigate problem

reply | This was helpful (7)

Rcpir 17-04-2022
If a plastic thread or string is wound on the head holder, how is it removed?

reply | This was helpful (3) (Translated by Google)

Gérard CROS 02-09-2021
When a wire is wound on the spindle, how do you remove the black casing that houses the cutting roller?

reply | This was helpful (0) (Translated by Google)

john 15-04-2026
I have a GLC3630L20 and it shuts off 2 seconds after i switch it on any idea what could be the problem

reply | This was helpful (0)

More about this manual

We understand that it’s nice to have a paper manual for your Black and Decker GLC3630L20 Grass Trimmer. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Black and Decker. They might be able to provide an original manual. Are you looking for the manual of your Black and Decker GLC3630L20 Grass Trimmer in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.