Manual Bertazzoni PM363I0X Hob

Manual

6

CONNECTING THE APPLIANCE TO THE GAS SUPPLY

Before connecting the appliance to the gas supply you first need to remove the plastic protective plug for the

gas supply which is inserted under pressure in the gas inlet connection. To remove the plug simply unscrew

it.

Then make sure that the details shown on the label on the lower part of the case are compatible with

those of the gas supply.

A label on the last page of this manual and on the lower part of the case indicates the conditions for

regulating the appliance: type of gas and pressure used.

IMPORTANT: This appliance must be installed in accordance with the norms in force of the country

concerned and it must only be used in a well-ventilated place.

ATTENTION: Remember that the gas inlet connection for the appliance is threaded 1/2 gas

cylindrical male in accordance with the norms UNI-ISO 228-1. (Fig. 10)

There are two ways to make the connection to the main gas line:

A. The hotplate can be connected with rigid pipe as specified in AS5601 table 3.1.

B. The hotplate can be connected with a Flexible Hose, which complies with AS/NZS 1869 (AGA Approved),

10mm ID, class B or D, no more than 1.2m long and in accordance with AS5601.

WARNING: Ensure that the hose assembly is restrained from accidental contact with the flue or flue outlet of

an underbench oven and it does not contact the hot surfaces of the hotplate, oven, dishwasher or other

separate appliance that may be installed underneath or next to the hotplate. The hose should not be

subjected to abrasion, kinking or permanent deformation and should be able to be inspected along its entire

length. Unions compatible with the hose fittings must be used and connections tested for gas leaks.

The supply connection point must be accessible with the appliance installed. Fit the supplied elbow and

gasket as shown in Fig.20. The gas inlet connection has a 1/2" BSP male thread. When making the

connection, take care not to apply excessive stress by counterbalancing tightening force. Ensure that the

available gas supply is the same as the gas type label affixed to the base of the hob. If not, contact

Bertazzoni for a Gas Conversion Kit. The gas supply pressure must be adjusted in accordance with the data

label for the gas type.

Natural Gas

The natural gas regulator supplied must be fitted for natural gas. Ensure the arrow on the regulator points

towards the direction of the gas flow. The test point pressure must be adjusted to 1.00 kPa with the largest

burner operating on maximum flame.

Propane Gas

Fit the Propane Gas test point assembly (supplied in the gas conversion kit). An AGA Approved gas

regulator suitable for a supply pressure of 2.75kPa should be part of the gas tank supply.

ELECTRICAL CONNECTION

The appliance is equipped with a 1.2 m. cable with 3 wires ready for connection to a dedicated 3 wire

grounded power supply/junction box: (fig 19).

Voltage 240 V AC, Frequency 60Hz. Max Current: 3700W /15.5 A

brown wire: connect to L1 (hot)

---------------: connect to L1 (hot)

blue wire: connect to N (neutral)

Yellow/Green wire: connect to GND (ground)

A dedicated line and junction box should be used to connect the oven to a 20 A circuit.

When connecting the cable directly to the mains, connection to the electricity supply must be made by an

authorised person in accordance with the Wiring Rules AS/NZS3000. The installation must include a suitable

isolating switch with a minimum contact opening of 3mm between the appliance and the mains. The isolating

switch should be sized according to the load on the data label and should comply with current regulations

(the earth wire should not be interrupted by the circuit breaker).

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Bertazzoni PM363I0X Hob. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Bertazzoni. They might be able to provide an original manual. Are you looking for the manual of your Bertazzoni PM363I0X Hob in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Bertazzoni Hobs
More manuals of Hobs

Frequently Asked Questions about Bertazzoni PM363I0X Hob

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Bertazzoni QB36600X Hob

Manual

Bertazzoni P604IM1B2NE Hob

Manual

Bertazzoni P905LMODX Hob

Manual

Bertazzoni P755CMODX Hob

Manual

Bertazzoni P804ICH2M30NC Hob

Manual

Bertazzoni P603I30NV Hob

Manual

Bertazzoni P301C6PROGNE Hob

Manual

Bertazzoni P302PROGNE Hob

Related categories