Manual Bartscher BIG 700 1F7 Hob

Manual

2.2 INSTALLATION OF THE APPLIANCE

Gas systems and the locations where the appliances are installed have to comply with the regulations in force in

the individual area, and in particular it has to be borne in mind that the air required for combustion equals 2m

3

/h

for each kW of power installed, besides the 35 m

3

/h per kW required for well-being in the rooms, and that accident

prevention Regulations must be complied with.

INSTALLING THE APPLIANCES IN POSITION

The appliances are for building into a worktop.

Remove the appliances from the packaging and set them up on the surface which is to be used, getting them level

and adjusting the height by the use of the adjustable feet or other means.

Remove the protective film from the outer panels, peeling it slowly to avoid the adhesive being left behind.

It is important that the walls adjacent to the appliance should be protected against heat, either by a layer of refractory

sheets or by maintaining a distance of at least 100 mm between the appliances and rear or side walls.

2.3 FUME EXTRACTION

The appliances must be installed in locations suitable for the discharge of the products of combustion. This must

be arranged in compliance with what is laid down in the installation regulations. Our appliances are rated as Type

A gas appliances (see tables of technical data), which are not expected to be connected to a natural duct for the

extraction of the products of combustion.

These appliances must discharge into suitable hoods, or similar devices, connected to a reliably working chimney

or directly to the exterior. Failing that, it is permissible to use an air extractor directly connected to the exterior,

with a suitable throughput, bearing in mind the air-changes necessary for the well-being of the operators.

The manufacturers of the appliance refuse to accept any responsibility for damage caused by incorrect

installation, tampering with the appliance, improper use, poor maintenance, failure to observe local

regulations or inexperience of the user.

Before going ahead with the connection, check on the data plate that the appliance has been tested and homologated

for the type of gas available at the user’s premises. In the event that the type of gas indicated on the plate is not the

gas which is available, follow the instructions in the paragraph “Conversion for operation with other types of gas”.

Check that the specification on the data plate matches the gas that is actually supplied. Also check that the supply

tallies with what is indicated below.

- Before connecting the appliance, make sure that the specifications on the data plate match those of the gas

distribution network.

- The appliance must be used by only personnel trained in its use.

This appliance must be used only for the purpose for which it has been expressly designed.

- Do not wash the appliance with direct high-pressure jets of water.

- Do not obstruct the openings or slots for air intake or heat dispersal.

- Do not continue using the appliance in the event of breakage or poor running.

- Before carrying out any cleaning or maintenance operations, disconnect the appliance from the gas supply network.

- To avoid the risk of oxidisation and chemical attack in general, the stainless steel surfaces should be kept well

cleaned.

- For any repairs, contact only an authorised service centre and insist on the use of original spare parts.

- If the appliance is not used for long periods of time, turn off the main gas tap, and wipe all the steel surfaces

vigorously with a cloth moistened with oil or vaseline so as to spread a protective coating over them; the area

where the appliance is located should also be aired periodically.

- Failure to comply with the above instructions could compromise the safety of the appliance.

Making the connections, setting the system and the appliances in operation and setting up the air intakes

and fume extraction are all tasks which must be carried out in accordance with the manufacturer’s

instructions by specialist professionals, in conformance with regulations in force. Current Fire Service

regulations must also be obeyed.

3. OPERATION WITH A GAS SUPPLY IDENTICAL

TO THAT FOR WICH THE APPLIANCE IS SET UP

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Bartscher BIG 700 1F7 Hob. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Bartscher. They might be able to provide an original manual. Are you looking for the manual of your Bartscher BIG 700 1F7 Hob in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Bartscher Hobs
More manuals of Hobs

Frequently Asked Questions about Bartscher BIG 700 1F7 Hob

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Bartscher BIG 700 2L5 Hob

Manual

Bartscher 104.909 Hob

Manual

Bartscher IK 30TCS Hob

Manual

Bartscher 1K1500 Hob

Manual

Bartscher BIG 700 2L3 Hob

Manual

Bartscher 1K221-T Hob

Manual

Bartscher 104.904 Hob

Manual

Bartscher BIG 700 1F8 Hob

Related categories