Home > Miscellaneous > Hand Dryers > ASI Hand Dryers > ASI 0141 Hand Dryer

Manual ASI 0141 Hand Dryer

Need a manual for your ASI 0141 Hand Dryer? Below you can view and download the PDF manual for free in English. This product currently has 0 frequently asked questions, 0 comments and has 0 votes. If this is not the manual you want, please contact us.

Is your product defective and the manual offers no solution? Go to a Repair Café for free repair services.

Manual

General safety information:

Installation

Installation Kit Included (find in carton)

-- NOTE: Do not install dryer over washbasin --

Operating Instructions and Parts Manual

Hand Dryer

Disconnect power at the

service breaker before installing or servicing.

This product is intended

for installation by a qualified service person.

Use AWG NO. 12 solid conductor for wiring.

All units must be supplied

with a 3-wire service. The ground wire must

be connected to the dryer's backplate.

Failure to properly ground

unit could result in severe electrical shock

and/or death.

www.americanspecialties.com

1. Make sure power supply breaker is switched off. Installation must be carried out in accordance

with the current edition of the local wiring regulations code having jurisdiction. Installation should

be performed only by a qualified electrician.

2. Place template against wall at desired height (see mounting height recommendations) and mark

locations of 4 mounting holes and wire service entry at knockout (KO) location.

Note: For two or more dryers, dryers should be no closer than 24 inches (610 mm) on center.

3. Remove and retain 2 cover screws and cover.

4. For in-wall (concealed) power supply - Provide supply wire to KO location according to local code

and attach securely to chassis at KO with appropriate strain relief connector (not supplied).

5. Attach dryer to wall. For wood wall/studs use ¯1/4 inch (M6) screws at length that will ensure

1 inch (25 mm) min. stud penetration. For masonry walls use expansion bolts or anchors for ¯1/4 inch

(M6) screws to ensure penetration 1/4 inch (6 mm) deeper than anchor. Shim if necessary to

ensure base plate is flat against wall.

6. Connect supply and ground wires to terminal block where indicated or connect supply wires to terminal

block where indicated and connect ground wire to base plate with ground screw (Connections: A.

Connect the live wire (colored Brown or Black) to the terminal block marked "L1". B. Connect the

neutral wire (colored White or Grey) or connect the second live wire (colored Red or Orange) to the

terminal block marked "N/L2". C. Connect the ground wire (colored green or green and yellow or bare

conductor) to the terminal block marked " " or to the green screw marked " "). Colors of live and

neutral wires depend on voltage of supply service and requirements of Building and Electrical Code

having jurisdiction.

7. Replace cover. Do not over-tighten screws.

1. Self-Threading screws 1/4" x 2-1/2" (M6 x 64) x 4 pcs

2. Security hex wrench 5/32" (4) L-Type x 1 pcs

06092857

Surface-mounted Automatic hand dryer

Rating

Let us know what you think about the ASI 0141 Hand Dryer by leaving a product rating. Want to share your experiences with this product or ask a question? Please leave a comment at the bottom of the page.

Are you satisfied with the ASI 0141 Hand Dryer?
Yes No

Be the first to rate this product

0 votes

Join the conversation about this product

Here you can share what you think about the ASI 0141 Hand Dryer. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.

More about this manual

We understand that it’s nice to have a paper manual for your ASI 0141 Hand Dryer. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact ASI. They might be able to provide an original manual. Are you looking for the manual of your ASI 0141 Hand Dryer in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.