Manual Panasonic SC-PM602 Stereo-set

Manual

Preparing the media

Disc

1 Press [CD x] (main unit: [x OPEN/CLOSE]) to open

the disc tray.

Put in a disc with the label facing up.

Press again to close the disc tray.

2 Press [USB/CD] to select “CD”.

USB

1 Decrease the volume and connect the USB device to

the USB port.

Hold the main unit when connecting or disconnecting

the USB device.

2 Press [USB/CD] to select “USB”.

Note:

Do not use a USB extension cable. The system cannot

recognise USB device connected through a cable.

Bluetooth

®

You can connect and play an audio device wirelessly

through Bluetooth

®

.

Preparation

• Switch on the Bluetooth

®

feature of the device and put

the device near the system.

• Read the operating instructions of the device for details.

Ű Pairing a device

Preparation

If this system is connected to a Bluetooth

®

device,

disconnect it (Z“Disconnecting a device”).

1 Press [ ].

If “PAIRING” is shown, continue with step 3.

2 Press [PLAY MENU] to select “PAIRING” and then

press [OK].

Or press and hold [ –PAIRING] on the main unit until

“PAIRING” is shown.

3 Select “SC-PM602” or “SC-PM600 ”from the

Bluetooth

®

menu of the device.

If prompted for a passkey, input “0000”.

The device connects with this system automatically

after pairing is complete.

The name of the connected device is shown for a few

seconds.

Note:

You can pair up to 8 devices with this system. If a 9th device is

paired, the device that has not been used for the longest time

will be replaced.

Ű Connecting a device

Preparation

If this system is connected to a Bluetooth

®

device,

disconnect it (Z“Disconnecting a device”).

1 Press [ ].

“BLUETOOTH READY” is shown.

2 Select “SC-PM602” or “SC-PM600 ” from the

Bluetooth

®

menu of the device.

The name of the connected device is shown for a few

seconds.

3 Start playback on the device.

Note:

• A device must be paired to connect.

• This system can only connect to one device at a time.

• When

“BLUETOOTH” is selected as the source, this

system will automatically try to connect to the last

connected device. (

“LINKING” is shown during this

process.)

Ű Disconnecting a device

1 Press [ ].

2 Press [PLAY MENU] repeatedly to select

“DISCONNECT?”.

3 Press [R, T] to select “OK? YES” and then press

[OK].

“BLUETOOTH READY” is shown.

To cancel, select “OK? NO”.

Using the main unit

Press and hold [ –PAIRING] until “PAIRING” is shown.

Note:

A device is disconnected when you:

• Select a different source.

• Move the device out of the maximum range.

• Disable the Bluetooth

®

transmission of the device.

• Switch off the system or the device.

Media playback

The following marks indicate the availability of the feature.

Basic playback

CD USB BLUETOOTH

Note:

Depending on the Bluetooth

®

device, some operations may

not work.

Viewing available information

CD USB BLUETOOTH

You can view the available information on the display

panel.

Press [DISPLAY].

Note:

• Maximum characters that can be shown: approximately 32

• This system supports ver. 1.0, 1.1 and 2.3 ID3 tags.

• Text data that the system does not support can show

differently.

• Example: MP3 album and track number display.

Play menu

CD USB

1 Press [PLAY MENU] repeatedly to select

“PLAYMODE” or “REPEAT”.

2 Press [R, T] to select the setting and then press

[OK].

Note:

• During random playback, you cannot skip to tracks which

have been played.

• The setting is cancelled when you open the disc tray or

disconnect the USB device.

Link mode

BLUETOOTH

You can change the link mode to suit the connection type.

Preparation

If this system is connected to a Bluetooth

®

device,

disconnect it (Z“Disconnecting a device”).

1 Press [PLAY MENU] repeatedly to select

“LINK MODE”.

2 Press [R, T] to select the mode and then press [OK].

Note:

• Depending on the device, the playback image and sound

may not be synchronised. In this case, select

“MODE 1”.

• Select “MODE 1” if the sound is interrupted.

CD :

USB :

BLUETOOTH :

CD-R/RW in CD-DA format or with MP3 files.

USB device with MP3 files.

Bluetooth

®

device.

Play Press [4/9].

Stop Press [8].

USB

The position is memorised.

“RESUME” is shown.

Press again to stop fully.

Pause Press [4/9].

Press again to continue playback.

Skip Press [2/3] or [5/6] to skip track.

CD USB

Press [R, T] to skip MP3 album.

Search Press and hold [2/3] or [5/6].

Album

number

Track

number

PLAYMODE

OFF

PLAYMODE

Cancel the setting.

1-TRACK

1

Play one selected track.

Press [2/3] or [5/6] to

select the track.

1-ALBUM

1

Play one selected MP3 album.

Press [R, T] to select the MP3 album.

RANDOM

RND

Play all tracks randomly.

1-ALBUM

RANDOM

1 RND

Play all tracks in one selected MP3

album randomly.

Press [R, T] to select the MP3 album.

REPEAT

OFF REPEAT Cancel the setting.

ON REPEAT Repeat playback.

MODE 1 Emphasis on connectivity.

MODE 2

(default)

Emphasis on sound quality.

Input level

BLUETOOTH

You can change the input level setting if the sound input

level of the Bluetooth

®

transmission is too low.

1 Press [PLAY MENU] repeatedly to select

“INPUT LEVEL”.

2 Press [R, T] to select the level and then press [OK].

Note:

Select

“LEVEL 0” if the sound is distorted.

Ű Note on disc

• This system can play CD-R/RW with CD-DA or MP3

format content.

• Before playback, finalise the disc on the device it was

recorded on.

• Some CD-R/RW cannot be played because of the

condition of the recording.

Ű Note on USB device

• This system supports USB 2.0 full speed.

• This system can support USB devices of up to 32 GB.

• Only FAT 12/16/32 file system is supported.

Ű Note on MP3 file

• Files are defined as tracks and folders are defined as

albums.

• Tracks must have the extension “.mp3” or “.MP3”.

• Tracks will not necessarily be played in the order you

recorded them.

• Some files can fail to work because of the sector size.

MP3 file on disc

• This system can access up to:

– 255 albums (including root folder)

–999 tracks

– 20 sessions

• Disc must conform to ISO9660 level 1 or 2 (except for

extended formats).

MP3 file on USB device

• This system can access up to:

– 800 albums (including root folder)

– 8000 tracks

– 999 tracks in one album

Sound effects

1 Press [SOUND] repeatedly to select the sound

effect.

2 Press [R, T] to select the setting and then press

[OK].

Note:

Changed settings will be kept until it is changed again, unless

otherwise indicated.

Saving the sound settings

You can save the current sound effects (up to

3 combinations).

Preparation

Select the sound effects.

1 Press [SETUP] to select “SAVE MY SOUND”.

2 Press [R, T] to select a sound setting number and

then press [OK].

“SAVED” is shown.

The new setting replaces the one existing in the same

sound setting number.

To recall the setting

1 Press [SOUND] to select “MY SOUND”.

2 Press [R, T] to select the sound setting number and

then press [OK].

(default)

MY SOUND “SOUND 1”, “SOUND 2” or “SOUND 3”

(Z“Saving the sound settings”)

PRESET EQ “HEAVY” (default), “SOFT”, “CLEAR”,

“VOCAL” or “FLAT”

BASS –4 to +4 (default: 0)

Using the main unit

1. Press [BASS/TREBLE] to select

“BASS”.

2. Press [2/3] or [5/6].

TREBLE –4 to +4 (default: 0)

Using the main unit

1. Press [BASS/TREBLE] to select

“TREBLE”.

2. Press [2/3] or [5/6].

D.BASS “ON D.BASS” (default) or “OFF D.BASS”

Using the main unit

Press [D.BASS] repeatedly.

SURROUND “ON SURROUND” or

“OFF SURROUND” (default)

DAB+

SC-PM602

Preparation

Press [RADIO] to select “DAB+”.

Note:

If you select

“DAB+” for the first time, the system will tune

automatically.

Manual tuning

1 Press [PLAY MENU] repeatedly to select

“MANUAL SCAN”.

2 Press [R, T] to select the frequency block and then

press [OK].

If no station is detected, “SCAN FAILED” is shown.

Adjust the antenna and try again.

To tune automatically

1 Press [PLAY MENU] to select “AUTOSCAN” and

then press [OK].

“START?” is shown.

2 Press [OK] to start tuning.

“DAB AUTO SCAN” is shown.

If no station is detected, “SCAN FAILED” is shown.

Do manual tuning.

Note:

Preset frequencies are erased after you do automatic tuning.

Memory presetting

You can preset up to 20 stations.

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2 Press [R, T] to select “STATION” and then press

[OK].

3 Press [2 /3] or [5/6] to tune in to the

station.

4 Press [OK].

5 Press [R, T] to select a preset number and then

press [OK].

Do steps 3 through 5 again to preset more stations.

The new station replaces any station that occupies the

same preset number.

Note:

You cannot preset a station when the station is not

broadcasting or when you have selected a secondary service.

Ű Selecting a preset station

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2 Press [R, T] to select “PRESET” and then press

[OK].

3 Press [2 /3] or [5/6] to select the preset

station.

Secondary service

You can listen to secondary services when “ ” is shown.

1 Press [PLAY MENU] repeatedly to select

“DAB SECONDARY”.

2 Press [R, T] to select the secondary service and

then press [OK].

To cancel, select “PRIMARY”.

Note:

The setting is cancelled when you select other stations.

Viewing available information

You can view the following information on the display

panel:

• Information about the DAB broadcast

• Programme type

• Ensemble label

• Frequency

•Time

Press [DISPLAY].

Checking the signal quality

You can check the signal quality when adjusting the

antenna.

1 Press [PLAY MENU] repeatedly to select

“SIGNAL QUALITY” and then press [OK].

The frequency block followed by the reception quality

is shown.

To select other frequency blocks, press [R, T].

2 Press [OK] again to exit.

Automatic clock adjustment

You can set the clock to update automatically.

1 Press [PLAY MENU] repeatedly to select

“AUTO CLOCK ADJ”.

2 Press [R, T] to select “ON ADJUST” and then press

[OK].

To cancel, select “OFF ADJUST”.

Frequency

block

Frequency Reception quality

0 (poor) to 8 (excellent)

Radio

Preparation

SC-PM602

Press [RADIO] to select “FM”.

SC-PM600

Press [RADIO] to select “FM” or “AM”.

Manual tuning

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2

Press [

R

,

T

] to select “MANUAL” and then press [OK].

3 Press [2/3] or [5/6] to tune in to the

station.

To tune automatically, press and hold the button until

the frequency starts changing quickly.

“STEREO” is shown when a stereo broadcast is being

received.

Memory presetting

SC-PM602

You can preset up to 30 FM stations.

SC-PM600

You can preset up to 30 FM stations and 15 AM stations.

Ű Automatic presetting

1 Press [PLAY MENU] to select “A.PRESET”.

2

Press [

R

,

T

] to select the setting and then press [OK].

The tuner presets all the stations it can receive into the

channels in ascending order.

To cancel, press [8].

Ű Manual presetting

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2

Press [

R

,

T

] to select “MANUAL” and then press [OK].

3 Press [2/3] or [5/6] to tune in to the

station.

4 Press [OK].

5 Press [R, T] to select a preset number and then

press [OK].

Do steps 3 through 5 again to preset more stations.

The new station replaces any station that occupies the

same preset number.

Ű Selecting a preset station

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2

Press [

R

,

T

] to select “PRESET” and then press [OK].

3 Press [2/3] or [5/6] to select the preset

station.

Improving the sound quality

When “FM” is selected

1 Press [PLAY MENU] repeatedly to select

“FM MODE”.

2 Press [R, T] to select “MONO” and then press [OK].

To cancel, select “STEREO”.

“MONO” is also cancelled when you change the

frequency.

To memorise the setting

Continue with step 4 of “Manual presetting”.

Checking the signal status

When “FM” is selected

Press [DISPLAY].

AM allocation setting

SC-PM600

This system can also receive AM broadcasts allocated in

10 kHz steps.

1 Press [RADIO] to select “AM”.

2 Press and hold [RADIO] on the main unit.

After a few seconds, the display panel shows the current

minimum radio frequency. Release the button when the

minimum frequency changes.

• To go back to the initial setting, do the above steps

again.

• Preset frequencies are erased after you change the

setting.

LOWEST Tuning begins from the lowest frequency.

CURRENT Tuning begins from the current frequency.

FM – – – – The FM signal is weak.

The system is not tuned in to a station.

FM ST The FM signal is in stereo.

FM MONO “MONO” is selected as the “FM MODE”.

The FM signal is in monaural.

Clock and timers

Setting the clock

This is a 24-hour clock.

1 Press [SETUP] repeatedly to select “CLOCK”.

2 Press [R, T] to set the time and then press [OK].

To check the time

Press [SETUP] repeatedly to select “CLOCK” and then

press [OK].

In standby mode, press [DISPLAY].

Note:

Reset the clock regularly to maintain accuracy.

Play timer

(Except for Bluetooth

®

source)

You can set the timer to come on at a certain time to wake

you up.

Preparation

Set the clock.

1 Press [SETUP] repeatedly to select “TIMER ADJ”.

2 Press [R, T] to set the start time and then press

[OK].

3 Do step 2 again to set the end time.

4 Press [R, T] to select the source you want to play

and then press [OK].

To start the timer

1 Press [SETUP] repeatedly to select “TIMER SET”.

2 Press [R, T] to select “SET” and then press [OK].

“#” is shown.

To cancel, select “OFF”.

The system must be switched off for the timer to

operate.

To check the setting

Press [SETUP] repeatedly to select “TIMER ADJ” and

then press [OK].

In standby mode, press [DISPLAY] two times.

Note:

• The timer starts at a low volume and increases gradually to

the preset level.

• The timer comes on at the set time every day if the timer is

on.

• If you switch off the system and then switch on again while a

timer is in operation, the timer will not stop at the end time.

Sleep timer

The sleep timer switches off the system after the set time.

1 Press [SETUP] repeatedly to select “SLEEP”.

2 Press [R, T] to select the setting (in minutes) and

then press [OK].

To cancel, select “OFF”.

Note:

• The remaining time is shown for a few seconds every

minute.

“SLEEP 1” is always shown when only 1 minute

remains.

• The sleep timer can be used together with the play timer.

• The sleep timer always comes first. Be sure not to set an

overlap of timers.

Others

Auto off

This system automatically switches off when you do not

use it for 20 minutes.

1 Press [SETUP] repeatedly to select “AUTO OFF”.

2 Press [R, T] to select “ON” and then press [OK].

To cancel, select “OFF”.

Note:

This function does not work when you are in radio source or

when a Bluetooth

®

device is connected.

Bluetooth

®

standby

This function automatically switches on the system when

you establish a Bluetooth

®

connection from a paired

device.

1 Press [SETUP] repeatedly to select

“BLUETOOTH STANDBY”.

2 Press [R, T] to select “ON” and then press [OK].

To cancel, select “OFF”.

Checking the software version

1 Press [SETUP] repeatedly to select “SW VER.” and

then press [OK].

The software version is shown.

2 Press [OK] again to exit.

Troubleshooting

Before requesting service, make the following checks. If

you are in doubt about some of the check points, or if the

solutions indicated do not solve the problem, consult your

dealer for instructions.

Ű Common problems

The unit does not work.

• The safety device has been activated. Do the following:

1. Press [1] on the main unit to switch the unit to standby

mode. If the unit does not switch to standby mode,

– Press and hold the button for a minimum of

10 seconds. Or,

– Disconnect the AC mains lead and connect it again.

2. Press [1] again to switch on the unit. If the problem

persists, consult your dealer.

No operations can be done with the remote control.

• Examine that the battery is installed correctly.

Sound is distorted or no sound.

• Adjust the volume of the system.

• Switch off the system, determine and correct the cause, and

then switch on again. It can be caused by straining of the

speakers through excessive volume or power, and when

using the system in a hot environment.

A humming sound can be heard during playback.

• An AC mains lead or fluorescent light is near the cables.

Keep other appliances and cords away from the cables of

this system.

Ű Disc

Display not shown correctly.

Playback does not start.

• You have not put in the disc correctly. Put it in correctly.

• Disc is dirty. Clean the disc.

• Replace the disc if it is scratched, warped, or non-standard.

• There is condensation. Let the system dry for 1 to 2 hours.

Ű USB

The USB device or the contents in it cannot be read.

• The format of the USB device or the contents in it are not

compatible with the system.

• USB devices with storage capacity of more than 32 GB

cannot work in some conditions.

Slow operation of the USB device.

• Large content size or large memory USB device takes longer

time to read.

The elapsed time shown is different from the actual play

time.

• Transfer the data to another USB device or backup the data

and reformat the USB device.

Ű Radio/DAB+

DAB+ reception is poor.

• Keep the antenna away from computers, televisions, other

cables and cords.

Sound is distorted.

• Use an optional outdoor antenna. The antenna should be

installed by a competent technician.

A beat sound is heard.

• Switch off the TV or move it away from the system.

• Move mobile telephones away from the system if the

interference is apparent.

A low hum is heard during AM broadcasts.

• Move the antenna away from other cables and cords.

Ű Bluetooth

®

Pairing cannot be done.

• Check the Bluetooth

®

device condition.

• The device is out of the 10 m communication range. Move

the device nearer to the system.

The device cannot be connected.

• The pairing of the device was unsuccessful. Do pairing

again.

• The pairing of the device has been replaced. Do pairing

again.

• This system might be connected to a different device.

Disconnect the other device and try pairing the device again.

The device is connected but audio cannot be heard

through the system.

• For some built-in Bluetooth

®

devices, you have to set the

audio output to “SC-PM602”or “SC-PM600”

manually.

Read the operating instructions of the device for details.

Sound from the device is interrupted.

• The device is out of the 10 m communication range. Move

the device nearer to the system.

• Remove any obstacle between the system and the device.

• Other devices that use the 2.4 GHz frequency band (wireless

router, microwaves, cordless phones, etc.) are interfering.

Move the device nearer to the system and distance it from

the other devices.

• Select

“MODE 1” for stable communication.

Playback image and sound are not synchronised.

• Restart the playback app of the device.

Ű Main unit displays

“--:--”

• You connected the AC mains lead for the first time or there

was a power failure recently. Set the clock.

“

ADJUST CLOCK”

• The clock is not set. Adjust the clock.

“

ADJUST TIMER”

• The play timer is not set. Adjust the play timer.

“

AUTO OFF”

• The system has not been used for 20 minutes and will

switch off within a minute. To cancel, press any button.

“

ERROR”

• An incorrect operation was done. Read the instructions and

try again.

“

F61”

“F77”

• Disconnect the AC mains lead and consult your dealer.

“F703”

• Examine the Bluetooth

®

connection.

• Disconnect the Bluetooth

®

device. Switch off the system

and then switch on again.

“

F76”

• There is a problem with the power supply.

• Disconnect the AC mains lead and consult your dealer.

“

NODEVICE”

• The USB device is not connected. Examine the connection.

“

NO DISC”

• You have not put in a disc.

“NO MEMORY”

• DAB memory presetting has not been done.

“

NO PLAY”

• Examine the content. You can only play supported format.

• The system may have a problem. Switch off the system and

then switch on again.

“NO SIGNAL”

• The station cannot be received. Adjust the antenna.

“

PLAYERROR”

• You played an unsupported MP3 file. The system will skip

that track and play the next one.

“

REMOTE 1”

“REMOTE 2”

• The remote control and the main unit are using different

codes. Change the code of the remote control.

– When “REMOTE 1” is shown, press and hold [OK] and [ ]

for a minimum of 4 seconds.

– When “REMOTE 2” is shown, press and hold [OK] and

[USB/CD] for a minimum of 4 seconds.

“SCAN FAILED”

• Stations cannot be received. Adjust the antenna or do

manual tuning.

“

SOUND 1 NOT SET”

“SOUND 2 NOT SET”

“SOUND 3 NOT SET”

• You have not saved the sound effects into the sound setting

number.

“

USB OVER CURRENT ERROR”

• The USB device is using too much power. Disconnect the

USB device, switch off the system and then switch on again.

“

VBR”

• The system cannot show the remaining play time for variable

bit rate (VBR) tracks.

Remote control code

When other Panasonic equipment responds to the remote

control of this system, change the remote control code for

this system.

Preparation

Press [USB/CD] to select “CD”.

Ű To set the code to “REMOTE 2”

1 Press and hold [CD] on the main unit and [USB/CD]

on the remote control.

“REMOTE 2” is shown.

2 Press and hold [OK] and [USB/CD] for a minimum of

4 seconds.

Ű To set the code to “REMOTE 1”

1 Press and hold [CD] on the main unit and [ ] on the

remote control.

“REMOTE 1” is shown.

2 Press and hold [OK] and [ ] for a minimum of

4 seconds.

System memory reset

Reset the memory when the following situations occur:

• There is no response when buttons are pressed.

• You want to clear and reset the memory contents.

1 Disconnect the AC mains lead.

2 While you press and hold [1] on the main unit,

connect the AC mains lead again.

Continue to press and hold the button until

“–––––––––” is shown.

3 Release [1].

All the settings are set back to the factory preset.

It is necessary to set the memory items again.

Maintenance

To clean this system, wipe with a soft, dry cloth.

• Never use alcohol, paint thinner or benzine to clean this

system.

• Before using chemically treated cloth, read the

instructions that came with the cloth carefully.

A5-16pp.indd 2A5-16pp.indd 2 2/18/16 12:57:00 PM2/18/16 12:57:00 PM

offset printing

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Panasonic SC-PM602 Stereo-set. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Panasonic. They might be able to provide an original manual. Are you looking for the manual of your Panasonic SC-PM602 Stereo-set in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Panasonic Stereo-sets
More manuals of Stereo-sets

Related products

Manual

Panasonic SC-PM04 Stereo-set

Manual

Panasonic SC-ALL5 Stereo-set

Manual

Panasonic SC-AKX660E Stereo-set

Manual

Panasonic SC-PM28 Stereo-set

Manual

Panasonic SC-HC400 Stereo-set

Manual

Panasonic SC-PMX70 Stereo-set

Manual

Panasonic SC-HC195 Stereo-set

Manual

Panasonic SC-HC15 Stereo-set

Related categories