PARTS LIST AND IDENTIFICATION
Please verify the contents of your MiNewt Pro 750 system
A. MiNewt Pro 750 Headlamp
B. Li-Ion Battery
C. Handlebar Mount
D. Low Prole Bike Helmet Mount
E. A/C Adapter
F. 36” Extension Cable
A.
B.
C.
D.
E.
F.
Knob
Hinge
DISCOVER THE NIGHT
Thank you for choosing the MiNewt Pro 750 from NiteRider, the
innovator in technical lighting systems. The MiNewt Pro 750
combines a high-powered white LED headlamp and a Li-Ion
battery.
To get the most from your NiteRider light, we urge you to
familiarize yourself with the following safety and operating
instructions.
MOUNTING THE LI-ION BATTERY
1. Thread the velcro strap through the slots on the bottom of
the battery.
2. Attach the concave surface of the battery to a safe,
convenient location on the handlebars, stem or frame,
placing the velcro strap over the mating surface.
MOUNTING THE HEADLAMP
The MiNewt Pro 750 headlamp can be mounted to the
handlebar or a helmet.
Straight Handlebar Mount
The Straight Handlebar Mount (SHM) is designed to t on
virtually any handlebar.
1. Turn the knob counter-clockwise,
allowing the hinge to swing open.
2. Place the mount on the handlebar
on either side of the stem, orienting
the rectangular notch in the slider clip
to the rear.
3. Swing the hinge down to make contact with the
handlebar.
4. Swing the bolt up, seating the knob into its recess.
5. Turn the knob clockwise to tighten and secure the
SHM to the handlebar.
To pivot the headlamp, push
the lever located under the
slider clip and rotate the
headlamp to the desired
position.
Inserting The Headlamp Into The Handlebar And Helmet Mounts
Insert the headlamp into the handlebar or helmet
mount slider clip from the rear
forward. Gently rocking the
lamp as you slide it may help.
Do not push the release lever
when inserting the headlamp
into the slider clip; let the lamp
snap into place by itself.
To remove the headlamp, push
the release lever and slide the
lamp backward.
Note: After mounting the headlamp, adjust it so the beam
illuminates the road properly without distracting oncoming
riders.
Helmet Mount
1. Unclamp the straps on each side of the helmet mount
and pull them free.
2. Position the plastic mounting
plate as close to the centerline
of the helmet as possible,
orienting the parallel grooves on
the slider clip to the rear.
3. Feed each strap into and out of two
helmet vents, circling each strap back
to the upper edge of the corresponding clamp.
4. Fasten the straps by inserting them into the clamps and snap
them shut.
OPERATION
1. Connect the headlamp cable to the battery.
2. Press and release the headlamp power button to turn the
light on. Cycle through the three brightness levels by
pressing and releasing the power button.
3. To access the daylight safety ash modes, press and hold
the power button until the headlamp starts to ash.
4. With the headlamp in ash mode, press and release the
power button to access Beacon, S.O.S. or Walk. From walk
mode you can access normal power by pressing and
releasing the power button.
5. To turn the headlamp o from normal, ash or walk modes,
press and hold the power button until the headlamp shuts o.
6. Always disconnect the battery from the headlamp when
transporting the light system to prevent accidentally
turning on the headlamp which may cause overheating
and potential damage from high heat or even a risk of re.
Join the conversation about this product
Here you can share what you think about the NiteRider MiNewt Pro 750 Bicycle Light. If you have a question, first carefully read the manual. Requesting a manual can be done by using our contact form.