Manual Bosch TDA7630GB Iron

Manual

Using Your Iron

1 Your iron

max.

N. Auto shut off

indicator lamp*

E. Water tankF. Soleplate

A. Shot of steam

D. Spray outlet

C. Steam regulator

B. Spray button

M. Power cable

K. Pilot light

H. Pointer

J. Max. Water

I. Temperature control

L. Water tank cover

G. "Clean" button

* Model dependent

2 Filling the water tank

 Set the steam regulator (C) to the position and

unplug the iron from the mains!

Use only clean water from the tap without mixing anything with

it. The addition of other liquids, such as perfume, will damage

the appliance.

Any damage caused by the use of the aforementioned

products, will make the guarantee void.

Do not use condensation water from tumble dryers, air conditioners

or similar appliances. This appliance has been designed to use

normal tap water.

To prolong the optimum steam function, mix tap water with distilled

water 1:1. If the tap water in your district is very hard, mix tap

water with distilled water 1:2.

You can inquire about the water hardness with your local water

supplier.

To prevent spillage of water out of the appliance in vertical position,

never fill beyond the “max” water level mark!

NO

9 After finishing each ironing session

1. Unplug the iron from the mains socket.

2. Set the steam regulator (C) to the position.

3. Open the water tank cover (L).

4. Hold the iron with the point facing up and shake it gently until

all the water has come out.

5. lf the iron is only slightly soiled, pull out the plug and allow the

soleplate to cool down. Wipe the housing and the soleplate

with a damp cloth only.

lf synthetic cloth melts due to too high temperature on the

soleplate, switch off the steam and rub off the residue immediately

with a thickly folded, dry cotton cloth.

6. Coil the power cable (M) loosely around the heel of the iron,

before storing.

7. Store the iron in an upright position.

10 Self Cleaning

The self clean function helps remove lime scale that has

built up around the steam valve.

This should be performed once every 3 or 4 uses.

1. When the iron is cold, slide the steam regulator (C) between the

and positions in quick succession about 3 or 4 times to

help loosen any lime scale and clean the valve inside.

2. Heat up the iron. Before starting ironing, hold the iron horizontally

over a sink and press the shot of steam button (A) 3 or 4 times.

This will help force out any lime scale and dirt deposits through

the holes in the soleplate.

11 Multiple de-scaling system

This range of irons is equipped with the following de-

scaling features “AntiCalc”.

A. self-clean

Each time you use the steam regulator (C), the “self-clean” system

cleans the mechanism of any scale deposits.

B. calc‘n-clean

The “calc’nclean” function helps to remove scale particles out

of the steam chamber. Use this function approximately every 2

weeks, if the water in your area is very hard.

1. Unplug the iron from the mains socket, set the steam regulator

(C) to the position and fill the water tank (E) with water.

2. Set the temperature selector (I) to the “max” position and plug

in the iron.

3. After the necessary warm-up period, the pilot light (K) goes out.

Then, unplug the iron (very important!).

4. Hold the iron over a sink. Press the “clean” button (G) until

approximately one third of the water capacity of the tank is

evaporated. Boiling water and steam will come out, carrying

scale or deposits that might be there.

5. Release the “clean” button, and gently shake the iron for some

seconds.

6. Repeat the steps 4 and 5 three times until the tank is empty.

Then plug the iron in and heat it up again until the remaining

water has evaporated.

7. Unplug the iron and let the soleplate (F) cool down. Wipe the

soleplate with a damp cotton cloth only.







C. anti-calc cartridge

The anti-calc cartridge has been designed to reduce the build-

up of scale produced during steam ironing, helping to extend

the useful life of your iron. Nevertheless, the “anti-calc” cartridge

cannot remove all of the scale that is produced naturally over time.

12 Anti-drip system “Drip Stop”

The irons in this range are equipped with an anti-drip system.

This will automatically stop the iron producing steam when the

selected temperature setting is too low to prevent water from

dripping out of the soleplate. You may hear a clicking sound when

this system is in operation.

Additional Features

13 Auto shut-off “secure”

(Model Dependent)

Some irons in this range are equipped with an auto-shut off

system.

The “secure” auto shut-off function switches off the iron

automatically when it is not being used, thus helping to prevent

accidents and saving energy. When the appliance is first plugged

in, this function will be inactive for the first 2 minutes to allow it to

reach the set temperature.

If during ironing, the iron is not moved for a certain length of time,

the iron will automatically switch off. The length of time will depend

on the position the iron has been left in:

Horizontally (flat) or on its side: 30 seconds

Vertically (upright): 8 minutes

The pilot light on the top of the handle (N) will flash when auto

shut-off has been activated. To switch the iron back on, move it

gently from side to side. The light will stop flashing.

Fabric protection soleplate cover “Protect”

(Model Dependent)

Some irons in this range are equipped with a fabric

protection soleplate cover

The fabric protector is used for steam-ironing delicate garments

at maximum temperature without damaging them. Use of the

protector also does away with the need for a cloth to prevent

shine on dark materials.

It is advisable to first iron a small section on the inside of the

garment to see if it is suitable.

To attach the fabric protection soleplate cover to the iron, place the

tip of the iron into the end of the fabric protector and press the rear

of the protector upward until you hear a click. To release the fabric

protector, pull down on the clip at the rear and remove the iron.













The protective cover can be purchased from After-sales or the

Bosch online shop.

Accessory code

(After-sales)

Name of accessory:

Protect cover soleplate

(online shop)

464851 TDZ1510

Cleaning and Maintenance

Attention ! Risk of burns !

For general cleaning, follow the information below:

Problem Solution

Dirty/lightly marked iron

body or soleplate

Clean the body of iron or soleplate with a damp

cloth then dry it.

Mark develops on

soleplate during use

Set the iron to its maximum temperature setting.

Rub the iron a few times over with a dry cotton

cloth folded several times.

Heavily stained soleplate While the iron is cold, iron a linen cloth soaked in

white vinegar. Then dampen a cloth with water

and wipe the soleplate clean and dry thoroughly.

DO NOT de-scale or clean the water tank with cleaning products

or solvents, as these could cause the iron to drip when using the

steam function.

DO NOT use a “professional steam cleaner” for cleaning the

appliance.

DO NOT use sharp objects or abrasive products to clean the soleplate

or any other part of the appliance. To keep the soleplate in good

condition, do not allow it to come into contact with metal objects.

Temperature

Setting

Steam Regulator

Setting

••• to “max”

••

Note: At a temperature setting of “•”, the soleplate is not hot

enough to produce steam so the steam regulator should be set

to the position to avoid water dripping from the soleplate (F).

Tip: for better ironing results, iron the last strokes without steam

to dry the garment.

5 Ironing with shot of steam

This can be used to remove stubborn wrinkles or to

press in a sharp crease or pleat. It cannot be used on a

synthetic setting for delicate items.

1. Set the temperature control (I) to the “•••” or “max” position.

2. Set the steam regulator (C) to the position.

3. Press the shot of steam (A) button on the handle repeatedly at

intervals of 5 seconds.

6 Vertical steaming with shot of steam

This can be used to remove creases from hanging

clothes, curtains etc. It cannot be used on a synthetic

setting for delicate items.

WARNING! Do not vertical steam while the item is being worn.

Never spray or aim steam at people or animals!

1. Make sure that there is water in the tank (E).

2. Set the temperature control (I) to the «•••» or «max» position

and the steam regulator (C) to the position.

3. Hold the iron in an upright position about 15 cm away from the

garment being steamed.

4. Press the shot of steam button (A) on the handle at intervals of

5 seconds, however, after 4 jets of steam, wait for 10 seconds

to allow for continued steam production.

7 Ironing without steam

This function enables the iron to be used for dry ironing.

1. Set the steam regulator (C) to the position.

2. Select an appropriate temperature for the type of material

being ironed.

8 Spray

This can be used to remove stubborn wrinkles.

1. Do not use the spray function with silk as staining may occur.

2. Make sure that there is water in the tank (E).

3. When ironing, press the spray button (B) and water will spray

out of the spray outlet (D) onto the garment.

3 Setting the temperature

The temperature control (I) adjusts the temperature of

the soleplate (F).

1. Check the temperature instructions shown on the care label of the

garment you are ironing and set the temperature control (I) to the

corresponding position by lining it up with the pointer (H) on the iron:

Fabric Temperature Setting

Synthetics •

Silk - Wool ••

Cotton - Linen •••

min

max

2. If you are unsure what type of material the garment is made from,

start ironing on the lowest temperature setting and increase

accordingly. If the garment is made from mixed fabrics, set the

temperature for the most delicate material.

3. For silk, woollen or synthetic materials iron the reverse side

of the fabric to prevent shiny patches. Avoid using the spray

function to prevent stains.

4. Sort your garments based on their care labels, always starting

with clothes that have to be ironed at the lowest temperature.

5. The pilot lamp (K) will stay lit while the iron is heating up and go

out once the selected temperature has been reached. Wait a

few seconds after the lamp goes out before you start ironing.

Once the iron is ready, you can continue to iron even if the pilot

lamp comes on again.

6. If your iron has auto shut-off and the pilot light (N) is flashing,

the auto shut-off has activated. Gently move the iron side to

side to restart it.

4 Ironing with steam

The steam regulator (C) is used to adjust the amount of

steam produced when ironing.

1. Make sure that there is water in the tank (E).

2. Adjust the temperature setting and then set the steam regulator

according to the table below. Steam will automatically be produced:

Rating

More about this manual

We understand that it’s nice to have a paper manual for your Bosch TDA7630GB Iron. You can always download the manual from our website and print it yourself. If you would like to have an original manual, we recommend you contact Bosch. They might be able to provide an original manual. Are you looking for the manual of your Bosch TDA7630GB Iron in a different language? Choose your preferred language on our homepage and search for the model number to see if we have it available.

Specifications

All manuals for Bosch Irons
More manuals of Irons

Frequently Asked Questions about Bosch TDA7630GB Iron

Our support team searches for useful product information and answers to frequently asked questions. If you find an inaccuracy in our frequently asked questions, please let us know by using our contact form.

Related products

Manual

Bosch TDA5660 Sensixx B4 Iron

Manual

Bosch TDA2443 Iron

Manual

Bosch TDA8366 Iron

Manual

Bosch TDS1440 Iron

Manual

Bosch TDA3637 Iron

Manual

Bosch TDI9015GB Sensixxx Iron

Manual

Bosch TDA5640 Iron

Manual

Bosch TDA2454 Iron

Related categories